# 3.4. Calculation of the nominal current¶

In order to stepper engine gave maximum torque, but it does not overheat, it is important to specify such technical characteristic as the rated current.

The greater a current in the motor winding, the greater the torque at the axis. It is important to remember that with an increase a current flowing through the winding, thermal power released by the motor increases. So the engine could operate for a long time allocated to thermal power (Joule heating) must be less power dissipation. Power dissipation can be calculated on the basis of documentation on the engine.

## 3.4.1. Calculation based on the parameters of unipolar full step mode¶

Power dissipation is equal to

where \(R_u\) - the resistance of the winding in unipolar mode, \(I_u\) - current through the winding in unipolar mode, \(n\) - the number of simultaneous windings.

Consider, for example, ST2818M1006. The table in the documentation shows that in full step mode simultaneously running two phase (n = 2) in the unipolar mode, i.e. \(P = 2 R_u I_u^2\). The motor controllers support only bipolar control mode. To switch from a unipolar to a bipolar mode, connect each phase windings in series, the resistance will increase, \(R_b = 2 R_u\), where \(R_b\) - the resistance of the series-connected windings in the bipolar control mode.

The motor controllers control algorithm is capable of operating in a microstepping mode and maintains the current so that the first winding current varies in function \(I_a \sin(\phi)\), in the other winding current varies in function \(I_a \cos(\phi)\), where \(I_a\) - current amplitude. Thermal power released two windings at any time

It follows from the foregoing that the \(I_a = I_u\).

## 3.4.2. Calculation based on the parameters of bipolar full step mode¶

Power dissipation is equal to \(P = n \cdot R_b I_b^2\), where \(R_b\) - the resistance of the winding in bipolar mode, \(I_u\) - current through the winding in bipolar mode, n - the number of simultaneous windings.

Consider, for example, ST2018S0604. The table in the documentation shows that in full step mode simultaneously running two phase (n = 2) in the bipolar mode, i.e. \(P = 2 R_b I_b^2\).

Thermal power dissipated in the motor windings that managed by motor controller, still is

We obtain the equation equating power \(2 R_b I_b^2 = R_b I_a^2\). We find that \(I_a = \sqrt{2} \cdot I_b\).

## 3.4.3. The relationship with an rms current¶

Alternating current in each motor winding can be characterized by its rms value in the period

Thermal power of **one** winding is
associated with an rms current through it \(P_1 = R_b
I_{rms}^2\). Both windings are identical \(P_1 = P_2\). The
total thermal power of the engine that is run by control by motor
controller controller \(P = P_1 + P_2 = 2 R_b I_{rms}^2\).

It follows from the foregoing that \(I_{rms} = \frac{I_u}{\sqrt{2}}\), also \(I_{rms} = I_b\).

## 3.4.4. Amplitude and rated current for BLDC¶

The rated motor current is calculated from the maximum allowable heat dissipation. The rated current written in the documentation is calculated from the power limit allocated when the power supply is connected to the two windings.

Let’s write the formula for power with this connection:

Formula for the power generated by the windings for sinusoidal control:

The rated motor current is calculated from the maximum allowable heat dissipation. Equate right parts of formulas:

So,

This means that if the documentation on your engine says that the rated current is, for example, 0.88A, then a amplitude current value can be written to the controller:

## 3.4.5. Setting the nominal current¶

Motor controller are capable of taking the nominal current value as a
current amplitude or as rms. The choice of which way to interpret the
input value of the nominal current is determined by the absence or
presence corresponding flag ENGINE_CURRENT_AS_RMS in the
*EngineFlags* engine settings
structure. When
setting the nominal current in XILab
should properly specify how the current is interpreted. Motor
controllers in this case will provide the maximum torque without
overheating the engine.

The same flag also controls the semantics of the BLDC current.

As for the stepper, there is a special checkbox in the XiLab for BLDC, which determines how to interpret the value entered in the Nominal current field. If checkbox “Amplitude current” is checked, the entered current value will be amplitude: maximum the amplitude of the sine will always be less than this value. If checkbox “Amplitude current” is cleared, the verified value will be recalculated by the formula for and the current amplitude will be limited already by this recalculated value

For all Standa motorized positioners prepared configuration files that contain the specified nominal current as rms. The corresponding flag is set. Thus the engines operate at optimum settings.